Library updates
Packs keep being revised after release. Here you'll find the current version of each one, what changed and how to update. Buyers get new versions without paying again, within the licence's update period.
- Sun Louvers pack
- Doors pack
- Gates pack
- Raised Floor, Ceilings & Partitions pack
- Rainscreen Facade pack
- Arviabim MVO Panel
Sun Louvers pack
current version 1.2.2Lighter louvers in 3D and a surface for each bay.
- Lighter 3D, same look: the blades and parts of each bay are built from just a few bodies (the Aerofoil, Rectangular Blade and Random Horizontal Slat Screen gain the most).
- Surface per bay: on the Bay by bay page, each bay on the map can have its own surface. Applies to the Aerofoil Louver, Rectangular Blade Louver, Movable Slat Panels, Fin and Slat Louver and Random Vertical Slat Screen.
- Fixing: "From foot to 1st bracket" and "From last bracket to top", to leave room for a cap, flashing or duct.
- Polygonal plan: dropping a vertex onto its neighbour deletes the vertex.
- Smoother dragging on large louvers: the quantity takeoff waits until you release the point before it is recalculated.
- With the Arviabim MVO Panel 1.6, version 1.2 louvers show a notice on the Arviabim page that a new version is available.
Previous versions
1.2
A new louver, the Random Horizontal Slat Screen, and density for the Random Vertical Slat Screen.
- Random Horizontal Slat Screen, new object: rows of slats along the length, with lengths randomised by density and fixed to at least two posts; layers and widths as in the vertical one; optional end mullions.
- Random Vertical Slat Screen: the fill setting became Density (%). At 100% the columns are full, with only the joints; below that, more empty columns and more spacing between the slats.
- The randomisation is less aligned: columns start at random heights and the joint doesn't always fall in the same bay.
- The Angle, Angle pattern and Bay by bay pages have been removed from both random slat screens, as they don't apply to fixed slats.
- With the Arviabim MVO Panel 1.5, version 1.1 louvers show a notice on the Arviabim page that a new version is available.
1.1
A new louver and the biggest revision of the pack so far.
- Honeycomb Louver, new object: a grid of crossed blades in panels, between the profiles or in front of the structure.
- Plan cut at the Floor Plan Cut Plane, with a cut fill; above the cut, you choose what is shown.
- Bay map: click each bay to set it with blades, empty, with its own angle or fixed.
- Polygonal plan edited by points, directly in the model.
- Revised fixing between slabs: slab-to-slab structure and clearances set with drag points.
- Openings that touch the edge cut the surround; drag points on the polygonal plan too.
- A notice on the Arviabim page when a new version of the Arviabim MVO Panel or of the pack itself is available, with a button to download it or see what changed.
1.0.2
Free polygon edited directly in 3D.
- Free outline with a point in the middle of each side: drag to create, move or delete vertices.
- When you switch to free polygon, the outline starts with the shape the louver already had.
- On a straight plan, pulling the end extends the louver on that side without moving it.
- Fin and Slat Louver: tracks and quantity takeoff follow the outline.
1.0.1
Lighter editing and new tilt options.
- Faster editing on large louvers: the quantity takeoff is only recalculated when the parts change.
- Light dragging: while you pull a point, the louver shows only the outline of each bay.
- Negative plane tilt, with the top facing the facade.
- "Structure only" option via the Arviabim panel in Model View Options.
1.0
First version of the pack.
Doors pack
current version 1.0.4New settings in all doors, with illustrations that follow your choices.
- Illustrations in the door's true proportions, with each dimension edited next to its arrow, right on the drawing.
- The illustration follows your choices: untick a part and it leaves the drawing; change a type and the illustration changes.
- Fire Door overhead closer redrawn as it is actually installed, following the opening.
- On the floor plan, the frame rebate follows the leaf side when the door is flipped.
- Canvas Strip Curtain Door: settings redone to the same standard as the other doors.
- Quantities that depend on the dimensions (louvre slats, frames, bars, fins) are shown already calculated.
- A notice on the "Door Leaf Type" page when a new version of the pack or of the Arviabim MVO Panel is available.
Previous versions
1.0.3
Settings open directly on the Arviabim page.
- Each new door opens on the leaf options ("Door Leaf Type"; on the Strip Curtain Door, "Strip curtain"). The design of the doors hasn't changed.
1.0.2
Library organisation.
- Objects appear directly in the Arviabim folder. Projects already using the pack stay linked.
1.0.1
Floor plan adjustments to hinged doors.
- The frame rebate sits on the leaf side in the floor plan, as in 3D.
- Architrave aligned with the edge of the rebate, in plan and in 3D.
1.0
First version of the pack.
Gates pack
current version 1.0.2New settings in all 6 gates, with illustrations that follow your choices.
- Illustrations in the gate's true proportions, with the dimensions edited next to their arrows.
- The sheet type is shown in section (corrugated, trapezoidal, shiplap, flat, grille) and changes with your choice.
- The leaf plan shows one or two leaves, the side and outward opening; a part switched off leaves the drawing.
- Sliding Gate with an illustration for each mounting type; Roller Shutter Door with the drawing of each slat.
- A notice on the "Arviabim" page when a new version of the pack or of the Arviabim MVO Panel is available.
Previous versions
1.0.1
Library organisation.
- Objects appear directly in the Arviabim folder. Projects already using the pack stay linked.
1.0
First version of the pack.
Raised Floor, Ceilings & Partitions pack
current version 1.1.1Lighter raised floor and ceilings in 3D.
- Raised Access Floor in "Fully detailed": panels as a single top with the joints, and lightweight pedestals, all visible.
- Modular Suspended Ceiling in "Fully detailed": tiles as a single top, lightweight T-profiles and hangers.
- Baffle Ceiling and Acoustic Cloud: lightweight hangers and cables, in a single body.
- "Full parts" option on the 3D page: when on, the 3D goes back to how it was, part by part. Sections and elevations always show the full parts.
- Raised Access Floor: segment numbers (T1, T2...) appear in any floor plan mode, via a checkbox on the Side closure page.
- With the Arviabim MVO Panel 1.6, version 1.1 objects show a notice on the Arviabim page that a new version is available.
Previous versions
1.1
The pack's biggest revision so far, with a more complete floor, ceilings and partitions.
- Raised Access Floor: side closure (edge fascia) per segment, with fixing angle, finishing profile (bullnose) and the sides of the ramp or step.
- Raised Access Floor: openings and free shape of the closure sheet, edited by points in 3D.
- Raised Access Floor: out-of-level slab, with height dimensions in 3D and polygonal recessed zones; the pedestals follow.
- Floor and ceiling: special panel map; choose the type and click the panels.
- Raised Access Floor: three floor plan modes, like the ceiling, with the new Panel layout.
- Floor and ceiling: a hole that crosses the outline becomes a cut-out, and a special panel next to a hole is cut or removed.
- Partitions: clickable module map, door markers to the Archicad standard and each door's data for the door schedule.
- Partitions: sloped end, to meet a sloping structure, inwards or outwards from the point.
- Glass Partition: openings for ducts and cable trays.
- A notice on the Arviabim page when a new version of the Arviabim MVO Panel or of the pack itself is available, with a button to download it or see what changed.
1.0
First version of the pack.
- Raised access floor, three ceilings (modular, baffle and acoustic cloud) and two partitions (demountable and glass).
Rainscreen Facade pack
current version 1.0.1Lighter facades in 3D and edge closures that follow the wall.
- Lighter 3D, same look: panels, returns and rivets are built from just a few bodies. Orbiting, selecting and editing a large facade area is now faster.
- Top and bottom closures at corners: both panels end at the same point on the wall, even when the wall isn't parallel to the segment.
- Wall that turns behind the facade: the closure panel, the counter-flashing upstand and the supports follow the wall.
- Fixing: "From foot to 1st bracket" and "From last bracket to top", to leave room for a cap, flashing or duct.
- Polygonal plan: dropping a vertex onto its neighbour deletes the vertex.
- With the Arviabim MVO Panel 1.6, version 1.0 facades show a notice on the Arviabim page that a new version is available.
Previous versions
1.0
First version: five parametric rainscreen facades, built on the same engine.
- Porcelain, ACM, Extruded Terracotta, HPL and Fibre Cement, and Perforated Corten.
- Panels laid out within the facade outline, on a straight, curved or polygonal plan, with openings.
- Edge closures and window trims: sill with drip, head and jambs.
- Perforated Corten with thousands of holes, yet light in Archicad: orbit, select and edit without lag.
Arviabim MVO Panel
current version 1.6Notices for the new versions of Sun Louvers, Raised Floor, Ceilings & Partitions and Rainscreen Facade.
- With the panel loaded, objects from earlier versions of the Sun Louvers pack, the Raised Floor, Ceilings & Partitions pack and the Rainscreen Facade pack show a notice that a new version is available.
- What you had already chosen for each view combination still applies.
Previous versions
1.5
Rainscreen facades in the panel, and the Sun Louvers pack 1.2.
- The louvers block now also applies to rainscreen facades: "Structure only" shows the assembly, without the blades and panels.
- With the panel loaded, version 1.1 louvers show a notice that a new version of the pack is available.
- What you had already chosen for each view combination still applies.
1.4
Panel layout in the raised floor plan, and the Raised Floor, Ceilings & Partitions pack 1.1.
- Raised floor in three floor plan modes, like the ceiling: Design, Panel layout (new) and Assembly.
- With the panel loaded, Raised Floor, Ceilings & Partitions objects (from 1.1 onwards) show a notice when a newer version of the pack comes out.
- What you had already chosen for each view combination still applies.
1.3
The panel now recognises the Gates pack 1.0.2.
- With the panel loaded, gates (from 1.0.2 onwards) show a notice when a newer version of the pack comes out.
- The options are the same as in 1.2; what you had already chosen still applies.
1.2
The panel now recognises the Doors pack 1.0.4.
- With the panel loaded, doors (from 1.0.4 onwards) show a notice when a newer version of the pack comes out.
- The options are the same as in 1.1; what you had already chosen still applies.
1.1
Illustrated panel and a new name.
- Each panel option appears as a button with an image of the result.
- The panel carries its version number, and objects show a notice when a newer one exists.
- Up to 1.0 the file was called "Arviabim-Base". It's the same panel; remove the old one from the Library Manager before adding the new one.
1.0
First version of the panel.
How to update a pack
- Sign in to your Hotmart account, open the pack under My purchases and download the current version file.
- Open the .zip and save the .lcf file in your permanent libraries folder.
- In Archicad, open File > Libraries and Objects > Library Manager.
- Remove the previous version of the pack from the list. Never keep two versions loaded at the same time.
- Click Add, choose the new .lcf and then Reload & Apply.
Questions? WhatsApp +55 47 9235-5526 · Back to the Library